请教关于SW的宏录制

甘aAnti露es · 发表于 2008-3-30 18:50:32

经典图书

我这有一个别人编好的一个应用程序,能在SW中生成直齿圆柱齿轮,我在SW中用宏录制它的齿轮程序,然后保存录制的VB程序,再打开在SW中却画不出整个齿轮,只画了一点溅开线,请问各位大侠是什么原因,?是不是画得太快了没录完整?下面是我录的VB程序,请大侠帮忙改正.
******************************************************************************
C:DOCUME~1OWNER~1.LENLOCALS~1Tempswx2856Macro1.swb - macro recorded on 03/30/08 by Owner
' ******************************************************************************
Dim swApp As Object
Dim Part As Object
Dim SelMgr As Object
Dim boolstatus As Boolean
Dim longstatus As Long, longwarnings As Long
Dim Feature As Object
Sub main()
Set swApp = Application.SldWorks
Set Part = swApp.ActiveDoc
Set SelMgr = Part.SelectionManager
swApp.ActiveDoc.ActiveView.FrameState = 1
swApp.ActiveDoc.ActiveView.FrameLeft = 0
swApp.ActiveDoc.ActiveView.FrameTop = 0
swApp.ActiveDoc.ActiveView.FrameState = 1
boolstatus = Part.Extension.SelectByID2("前视基准面", "PLANE", 0, 0, 0, False, 0, Nothing, 0)
Part.SketchSpline 11, 0.001514327489425, 0.04197269126771, 0
Part.SketchSpline 10, 0.00110920446142, 0.04118310844044, 0
Part.SketchSpline 9, 0.000782345579599, 0.04045947027597, 0
Part.SketchSpline 8, 5.260760219714E-04, 0.0398074035427, 0
Part.SketchSpline 7, 3.323653043098E-04, 0.0392319294476, 0
Part.SketchSpline 6, 1.928687744332E-04, 0.03873744270738, 0
Part.SketchSpline 5, 9.897028159602E-05, 0.03832769326035, 0
Part.SketchSpline 4, 4.182586044328E-05, 0.03800577068273, 0
Part.SketchSpline 3, 1.240826563044E-05, 0.03777409136366, 0
Part.SketchSpline 2, 1.552190382288E-06, 0.03763438848369, 0
Part.SketchSpline 1, 0, 0.03758770483144, 0
Part.SketchSpline 0, 0, 0.0375, 0
Part.SketchSpline 11, 0.003033341513997, 0.0418903191592, 0
Part.SketchSpline 10, 0.003350706018885, 0.04106155774601, 0
Part.SketchSpline 9, 0.003597396355362, 0.04030681752608, 0
Part.SketchSpline 8, 0.003781650800771, 0.03963086234254, 0
Part.SketchSpline 7, 0.003911995725673, 0.03903781556797, 0
Part.SketchSpline 6, 0.003997202079717, 0.03853114378532, 0
Part.SketchSpline 5, 0.004046240994833, 0.03811364322113, 0
Part.SketchSpline 4, 0.004068238672279, 0.03778742897706, 0
Part.SketchSpline 3, 0.00407243072231, 0.03755392709594, 0
Part.SketchSpline 2, 0.004068116127092, 0.03741386948882, 0
Part.SketchSpline 1, 0.004064610998589, 0.03736729173924, 0
Part.SketchSpline 0, 0.004055126886056, 0.03728010120611, 0
boolstatus = Part.Extension.SelectByID2("Spline1", "SKETCHSEGMENT", 1.893614260938E-05, 0.03072390945709, 0, False, 0, Nothing, 0)
boolstatus = Part.Extension.SelectByID2("Arc2", "SKETCHSEGMENT", -2.789608646826E-04, 0.03045911211728, 0, True, 0, Nothing, 0)
Part.ClearSelection2 True
boolstatus = Part.Extension.SelectByID2("Spline1", "SKETCHSEGMENT", 1.893614260938E-05, 0.03072390945709, 0, False, 1, Nothing, 0)
boolstatus = Part.Extension.SelectByID2("Arc2", "SKETCHSEGMENT", -2.789608646826E-04, 0.03045911211728, 0, True, 1, Nothing, 0)
Part.SketchFillet2 0.0006, 2
Part.ClearSelection2 True
boolstatus = Part.Extension.SelectByID2("Spline2", "SKETCHSEGMENT", 0.003825397902451, 0.03051427822974, 0, False, 0, Nothing, 0)
boolstatus = Part.Extension.SelectByID2("Arc2", "SKETCHSEGMENT", 0.004123294909743, 0.03020534799996, 0, True, 0, Nothing, 0)
Part.ClearSelection2 True
boolstatus = Part.Extension.SelectByID2("Spline2", "SKETCHSEGMENT", 0.003825397902451, 0.03051427822974, 0, False, 1, Nothing, 0)
boolstatus = Part.Extension.SelectByID2("Arc2", "SKETCHSEGMENT", 0.004123294909743, 0.03020534799996, 0, True, 1, Nothing, 0)
Part.SketchFillet2 0.0006, 2
Part.ClearSelection2 True
Part.ShowNamedView2 "*上下二等角轴测", 8
Part.ClearSelection2 True
Part.FeatureManager.FeatureExtrusion2 True, False, False, 0, 0, 0.004, 0.01, False, False, False, False, 0.01745329251994, 0.01745329251994, False, False, False, False, 1, 1, 1, 0, 0, False
boolstatus = Part.Extension.SelectByID2("", "EDGE", 0.002123763862755, 0.04201284627061, 0.003902629668346, True, 0, Nothing, 0)
boolstatus = Part.Extension.SelectByID2("", "EDGE", 0.002192423729468, 0.04194897752666, -9.125964368195E-06, True, 0, Nothing, 0)
Part.FeatureManager.InsertFeatureChamfer 4, 1, 0.001, 0.7853981633975, 0, 0, 0, 0
boolstatus = Part.Extension.SelectByID2("", "EDGE", 0.00143629687409, 0.04202786724477, 0.002109491707586, True, 0, Nothing, 0)
boolstatus = Part.Extension.SelectByID2("", "EDGE", 0.002941002379657, 0.04195561278704, 0.002066257852277, True, 0, Nothing, 0)
Part.ClearSelection2 True
boolstatus = Part.Extension.SelectByID2("", "EDGE", 0.00143629687409, 0.04202786724477, 0.002109491707586, False, 0, Nothing, 0)
boolstatus = Part.Extension.SelectByID2("", "EDGE", 0.002941002379657, 0.04195561278704, 0.002066257852277, True, 0, Nothing, 0)
Part.ClearSelection2 True
boolstatus = Part.Extension.SelectByID2("", "EDGE", 0.00143629687409, 0.04202786724477, 0.002109491707586, False, 1, Nothing, 0)
boolstatus = Part.Extension.SelectByID2("", "EDGE", 0.002941002379657, 0.04195561278704, 0.002066257852277, True, 1, Nothing, 0)
Part.FeatureFillet5 195, 0, 0, 0, 0, 0, 0
boolstatus = Part.Extension.SelectByID2("上视基准面", "PLANE", 0, 0, 0, True, 0, Nothing, 0)
boolstatus = Part.Extension.SelectByID2("右视基准面", "PLANE", 0, 0, 0, True, 0, Nothing, 0)
Part.InsertAxis2 True
boolstatus = Part.Extension.SelectByID2("基准轴1", "AXIS", 0, 0, 0, True, 0, Nothing, 0)
boolstatus = Part.Extension.SelectByID2("拉伸1", "BODYFEATURE", 0, 0, 0, True, 0, Nothing, 0)
boolstatus = Part.Extension.SelectByID2("倒角1", "BODYFEATURE", 0, 0, 0, True, 0, Nothing, 0)
Part.ClearSelection2 True
boolstatus = Part.Extension.SelectByID2("基准轴1", "AXIS", 0, 0, 0, True, 0, Nothing, 0)
boolstatus = Part.Extension.SelectByID2("拉伸1", "BODYFEATURE", 0, 0, 0, True, 0, Nothing, 0)
boolstatus = Part.Extension.SelectByID2("倒角1", "BODYFEATURE", 0, 0, 0, True, 0, Nothing, 0)
Part.ClearSelection2 True
boolstatus = Part.Extension.SelectByID2("基准轴1", "AXIS", 0, 0, 0, False, 1, Nothing, 0)
boolstatus = Part.Extension.SelectByID2("拉伸1", "BODYFEATURE", 0, 0, 0, True, 4, Nothing, 0)
boolstatus = Part.Extension.SelectByID2("倒角1", "BODYFEATURE", 0, 0, 0, True, 4, Nothing, 0)
Set Feature = Part.FeatureManager.FeatureCircularPattern2(40, 0.1570796326795, False, "NULL", False)
Part.ClearSelection2 True
boolstatus = Part.Extension.SelectByID2("前视基准面", "PLANE", 0, 0, 0, False, 0, Nothing, 0)
Part.ClearSelection2 True
Part.CreateLine2 -0.002, 0.0072284161474, 0, -0.002, 0.0098, 0
Part.CreateLine2 -0.002, 0.0098, 0, 0.002, 0.0098, 0
Part.CreateLine2 0.002, 0.0098, 0, 0.002, 0.0072284161474, 0
Part.ClearSelection2 True
boolstatus = Part.Extension.SelectByID2("Line3", "SKETCHSEGMENT", 0, 0, 0, False, 0, Nothing, 0)
Part.FeatureManager.FeatureCut True, False, True, 1, 0, 0.01, 0.01, False, False, False, False, 0.01745329251994, 0.01745329251994, False, False, False, False, 0, 1, 1
boolstatus = Part.Extension.SelectByID2("", "EDGE", -1.839064569253E-04, -0.007516792208207, 0.004027435487217, True, 0, Nothing, 0)
Part.ShowNamedView2 "*后视", 2
boolstatus = Part.Extension.SelectByID2("", "EDGE", 0, -0.0073025, 0, True, 0, Nothing, 0)
Part.FeatureManager.InsertFeatureChamfer 0, 1, 0.001, 0.7853981633975, 0, 0, 0, 0
boolstatus = Part.Extension.SelectByID2("点1@原点", "EXTSKETCHPOINT", 0, 0, 0, False, 0, Nothing, 0)
Part.BlankSketch
boolstatus = Part.Extension.SelectByID2("基准轴1", "AXIS", 0, 0, 0, False, 0, Nothing, 0)
Part.BlankRefGeom
Part.ShowNamedView2 "*上下二等角轴测", 8
Part.ViewDisplayShaded
End Sub